Home » Shop » KLEIBERIT 303.0 PVAc D3 wood adhesive, 0.5 kg

KLEIBERIT 303.0 PVAc D3 wood adhesive, 0.5 kg

90.00 MDL

KLEIBERIT 303.0 PVAc D3 wood adhesive, 0.5 kg. Ready to use for D3; reaches D4 with 5% 303.5 ME hardener. For windows, doors, stairs, veneer and HPL. Assembly time: 6–10 minutes at 20 °C.

Addon Details
KLEIBERIT 303.0 PVAc D3 wood adhesive, 0.5 kg 90.00 MDL
Subtotal
SKU: 303.0.8101 Category:
Description

KLEIBERIT 303.0 PVAc D3 wood adhesive, 0.5 kg

KLEIBERIT 303.0 is a ready-to-use PVAc wood adhesive for joinery that needs a strong, moisture-resistant bond. Use it on its own for D3 performance under DIN EN 204. For D4, add 5% KLEIBERIT 303.5 ME hardener: for example, 50 g per 1 kg of adhesive. Mix thoroughly and use the mixture within approximately 24 hours.

Benefits

  • No mixing is needed when D3 performance is sufficient.
  • Suitable for cold, hot and high-frequency bonding.
  • Bonds hard and exotic timbers with high strength.
  • The dried glue line is colourless without hardener; with hardener, it may be slightly yellow.

Where to use it

Windows, doors, stairs, tenon joints, veneering and HPL surface bonding, as well as partitions and other joinery components.

Working parameters

Base and colour PVAc dispersion; white
Time to assemble after application 6–10 minutes at 20 °C
Spread rate 100–130 g/m² for veneer; 150–200 g/m² for solid wood
Working temperature Ideally 18–20 °C; do not use below +10 °C
Press pressure 0.7–1.0 N/mm² for laminations and laminated wood
Time in the press Edge joints: from 15 minutes at 20 °C; from 5 minutes at 50 °C with preheating; from 2 minutes at 80 °C. HPL: 15–20 minutes at 20 °C, approximately 5 minutes at 50 °C, 1–2 minutes at 80 °C. Increase these times by approximately 50% when using hardener.
After pressing Final strength and the declared water-resistance class are reached after 7 days.
Equipment settings Density approximately 1.10 g/cm³; pH approximately 3; viscosity at 20 °C: 12,000 ± 2,000 mPa·s.
Pack size 0.5 kg

How to apply

Remove dust, oil and grease. Let the workpieces reach the workshop temperature. Recommended wood moisture is 8–10% for indoor work and 10–14% for windows. Applying to one face is normally enough, using a brush, spatula, roller or glue spreader. Apply to both faces for hard and exotic timbers. Assemble within the stated time and clamp. Use stainless-steel or plastic equipment; some timbers may discolour, especially on contact with iron.

Times and spread rates are guides: temperature, humidity, coat thickness and material absorbency affect the result. Check the settings on your own workpieces before starting a production run. Restricted to professional users.

Cleaning

Wash fresh adhesive from tools and equipment with water before it dries.

Storage

Approximately 12 months at 20 °C in the original sealed container. For 303.0, the manufacturer separately specifies at least 18 months in original 0.5 and 1 kg bottles, 5 kg canisters and 10 kg pails; this applies specifically to those factory containers. The adhesive tolerates freezing down to approximately −30 °C. Before use, warm it slowly to room temperature and stir well.

Buy from ABN

ABN supplies original KLEIBERIT adhesives, provides technical consultation and delivery throughout Moldova.

Frequently asked questions

Is hardener necessary?

Not for D3. For D4, add 5% KLEIBERIT 303.5 ME. The mixed adhesive has a working life of approximately 24 hours.

Can the joint be fully loaded as soon as it leaves the press?

Pressing time and final strength are different stages. The declared strength under DIN EN 204 is reached after 7 days.

Manufacturer’s technical data sheet (TDS)